Table of Contents
How do you reset the fuel gauge on a 2008 Hyundai Santa Fe?
How do you reset the fuel gauge on a Hyundai Santa Fe?
- Turn the ignition switch to the “On” position.
- Press the “Odo/Trip” button until the odometer is put into “ODO” mode.
- Turn off the ignition.
- Press and hold the “Odo/Trip” button.
- Release the “Odo/Trip” button.
Why is my fuel gauge not going up?
An inaccurate fuel tank reading is most commonly caused by the sending system which reads the fuel tank level and sends the reading to the gauge. Issues can also stem from a bad gauge, blown fuses, or corroded wiring. You can self-test all of these parts at home with a few tools.
How do I reset my electronic fuel gauge?
How to Reset a Fuel Gauge
- Turn the ignition switch to the “On” position.
- Press the “Odo/Trip” button until the odometer is put into “ODO” mode.
- Turn off the ignition.
- Press and hold the “Odo/Trip” button.
- Release the “Odo/Trip” button.
Is there a fuse for the fuel gauge?
Check the Fuses Particularly if you are experiencing an issue with more than one gauge on your vehicle, the culprit may be a fuse. If the fuse for the instrument panel has been blown, make sure to replace it. If the fuel gauge doesn’t sort itself out automatically, run the cluster test again.
What is a fuel level sensor?
A fuel level sensor (FLS) is used in all automobiles to indicate fuel level. Various methods are used to measure fuel level such as resistive film, discrete resistors, capacitive, and ultrasonic. These sensors are mechanically connected to a float which moves up or down depending on the fuel level.
What does Engine code P2068 mean?
fuel level sensor
What the P2068 code means. This code indicates the fuel level sensor is indicating a higher than expected voltage. The higher the value the more fuel is in the tank.
How do you know if your fuel gauge is not working?
Turn on the engine’s ignition and probe with a multimeter between the ground and the positive terminal on the back of the gauge; it should be marked with a “+” or an “I.” If there is no voltage then the fault is in the ignition circuit—and the gauge is probably good.
How do I fix my gas gauge not working?
How do you fix an inaccurate fuel gauge?
- Turn the ignition on and off a few times, and observe if the needle on the fuel gauge moves.
- Test the grounding wire on the sending unit of the fuel tank.
- Disconnect the wiring connected to the sending unit of the fuel gauge and then look at the fuel gauge.
How do you fix a stuck fuel gauge?
Check the grounding wire on the fuel gauge. To do so, connect the negative jumper cable to the vehicle’s frame and the positive cable to the fuel gauge’s grounding terminal. Turn the ignition to the on position and look at the fuel gauge. If the gauge is not working, then the grounding wire needs to be replaced.
Is the fuel gauge on my Santa Fe working?
2009 Hyundai Santa Fe with 81,000 miles. Fuel gauge started “failing” about 3 months ago… Sometimes drops to empty when fuel is in tank. Fill-up … read more
What should I do if my Hyundai fuel gauge is wrong?
If you encounter a Hyundai Fuel gauge readings wrong or erratic condition on the vehicles listed below or find any of the following trouble codes: P0461, P0462, P0463, B1562, perform the tests shown below. What causes erratic fuel gauge readings or wrong fuel gauge readings?
What was the problem with my Hyundai Santa Fe?
The first problem was with the gas gauge. When the tank was about half full, the electronic gauge would register empt … read more Subaru and Nissan factory training. In my 2008 Santa fe my check engine light came on and now my gas gauge says I am empty after fueling and does not show accurate fuel levels.
Is there recall on Hyundai Santa Fe fuel level sensor?
THIS IS RIDICULOUS AND DANGEROUS, AND HYUNDAI NEEDS TO RECALL THE FUEL LEVEL SENSORS DUE TO SAFETY PURPOSES. BECAUSE OF THIS NEAR ACCIDENT, I WENT AHEAD AND REPLACED BOTH SENSORS, COST $400.
https://www.youtube.com/watch?v=AvrUEBFQxEs