Table of Contents
What information must be included on a lockout/tagout device?
Both locks and tags must clearly indicate the identity of the employee who applied the device. This provides positive identification as to who is servicing the machinery and equipment. The identification will also indicate who may not have finished working in a multiple lockout/tagout situation.
What is OSHA requirement for lockout/tagout materials?
What are the requirements for the lockout and tagout devices? Must be durable, so that they are capable of withstanding the environment to which they are exposed for the maximum period of time that exposure is expected [29 CFR 1910.147(c)(5)(ii)(A)(1)]. Must be singularly identified [29 CFR 1910.147(c)(5)(ii)].
What is OSHA lockout/tagout procedure?
“Lockout/tagout” refers to specific practices and procedures. to safeguard employees from the unexpected energization or. startup of machinery and equipment, or the release of hazardous. energy during service or maintenance activities.1 This requires, in part, that a designated individual turns off and disconnects.
What are the specific required components that must be included in a lock out/tag out procedure?
OSHA requires three basic elements in a lock-out tag-out program. These are training, written procedures, and inspections. Training is required for two types of people; “authorized employees” and “affected employees.” Authorized employees are people who do the maintenance or servicing work.
What are the steps of lockout tagout?
An effective lockout/tagout program should include the following eight steps.
- Step 1: Detailed procedures for equipment.
- Step 2: Notify affected employees.
- Step 3: Shut down equipment properly.
- Step 4: Disconnect all primary energy sources.
- Step 5: Address all secondary sources.
- Step 6: Verify the lockout.
What devices are positive restraints that no one can remove without a key?
Lockout devices hold energy-isolation devices in a safe or “off” position. They provide protection by preventing machines or equipment from becoming energized because they are positive restraints that no one can remove without a key or other unlocking mechanism.
What are the 6 steps to LOTO?
Six Steps of LOTO Safety & Lockout/Tagout Procedures
- Preparation.
- Shutdown.
- Isolation.
- Lockout/tagout.
- Stored energy check.
- Isolation verification.
Who can remove a lockout/tagout device?
employee
Lockout or tagout device removal: Each lockout or tagout device must be removed from the energy-isolating device by the employee who applied the device [29 CFR 1910.147(e)(3)].
What are the 7 steps of Loto?
LOTO Safety: 7 Steps of lockout tagout
- Prepare for shutdown.
- Notify all affected employees of the activities and equipment involved.
- Shut down the equipment.
- Isolate the equipment from the hazardous energy source.
- Dissipate residual energy.
- Apply applicable lockout or tagout devices.
How to create a personal lockout tag template?
These tag templates meet federal Occupational Safety and Health Administration (OSHA) requirements for uniformity. For additional information on lockout/tagout equipment and how to attach a tag, see Control of Hazardous Energy: General Requirements(SLAC-I-730-0A10S-004). Personal Lockout Tag Follow these steps to create a personal lockout tag:
When to do lock out / tag out procedures?
Company Name . Lock out/Tag Out procedures are to be completed before any service or maintenance work on equipment or machinery, and/or before entry into any grain bin or other area where operating equipment poses a hazard to the entrant. Failure to follow proper lockout-tag out procedures may result in [&disciplinary&] [&action&] up to and
What are the requirements for a lockout device?
Lockout devices must work under the environmental conditions in which they are used.Tagout device warnings must remain legible even when they are used in wet, damp, orcorrosive conditions. Lockout and tagout devices must be designated by color, shape, or size. Tagout devices musthave a standardized print and warning format.
What are the procedures for minimal lockout procedures?
(2) The authorized employee shall refer to the company procedure to identify the type and magnitude of the energy that the machine or equipment utilizes, shall understand the hazards of the energy, and shall know the methods to control the energy. Type (s) and magnitude (s) of energy, its hazards and the methods to control the energy.