Table of Contents
How expensive is Dricore?
DRICORE System Panels are 2′ x 2′ square. This means that DRICORE costs about $1.56 per square foot. DRICORE estimates that 205 panels are needed for this space. Total DRICORE cost is $1,281, not including tax and shipping.
Which is better Dricore or barricade?
DRICORE Subfloor covers cold, damp concrete to protect and insulate your floor (R-Value of 1.4). BARRICADE Subfloor Air Plus softens finished floors to cushion against the hard concrete. Its sturdy confection supports over 6,600 pounds per square feet.
Should I use Dricore?
As a brand, DRIcore is great for subflooring a basement with low to mid-range moisture problems. The panels are made from OSB as well as a premade moisture barrier, which is typically constructed of polyethylene or durable foam. It is a lot like insulating a floor, but with the added protection of a water barrier.
How many Dricore panels are in a pallet?
DRIcore Engineered Subfloor Panel System (pallet of 120)
Can you nail into Dricore?
FASTENING PANELS TO CONCRETE Remember that DRIcore must be installed as a floating floor. Normally it is not recommended to nail, glue or screw DRIcore panels to the concrete surface. In some instances, we suggest minimal fastening of the panels to the concrete surface.
What is the cheapest subfloor material?
OSB
Rarely, a prospective homeowner may recognize that OSB is the cheaper subfloor material.
Is Dricore a vapor barrier?
A rubber pad is essentially a vapor barrier and will trap moisture. Or you could use a dricore underlayment as mentioned above, this will completely separate the carpet from any moisture.
Is Dricore and barricade the same?
Dricore is a hard plastic under OSB as opposed to OVRX Barricade which is more flexible hard foam. Both allow any water that gets under them to flow away.
Do you need underlayment with Dricore?
Engineered Hardwood Before installing glue-down or nail-down floors a 3/8″ plywood underlayment should be fastened to DRICORE® using 3/4” 18 gauge narrow crown staples. When installing nail-down floors test a piece of the finished floor to make sure the fastener does not puncture the plastic membrane.
How is Dricore calculated?
Estimating is easy. The total square footage of your room divided by 3.3 equals the number of panels you need. This factor includes an allowance for normal wastage and cutting around obstacles and pipes. To calculate how many panels you need.
Can you screw down DRIcore?
Remember that DRIcore must be installed as a floating floor. Normally it is not recommended to nail, glue or screw DRIcore panels to the concrete surface. In some instances, we suggest minimal fastening of the panels to the concrete surface.
How is DRIcore calculated?
How much does dricore subfloor system cost per square foot?
DRIcore estimates that 205 squares are needed to cover a space of 675 square feet. The total DRIcore cost to cover that space is $1,283, not including tax and shipping. Basement subfloor systems like DRIcore are all about convenience and shaving down subfloor height.
Can you install dricore panels over concrete slab?
I plan to be… Dear William: No. Dricore panels must be installed directly on top of the concrete slab. You should also install 3/4″ plywood over the DriCore panels, which flex a bit due to the rubber layer on the bottom.
How long does dricore subfloor panel last for?
Backed by a 25 year limited warranty, be confident when you choose DRICORE ® Subfloors. underneath DRICORE ® subfloor panels to quickly adjust the height by up to 1/4”.
What does dricore raised subfloor membrane panel do?
DRICORE. is the one-step engineered subfloor solution that is specifically designed for basements. The raised moisture barrier covers cold, damp concrete to protect, insulate and cushion your finished floors. Concrete continually releases moisture.